缪小吉,宋璐,卢阳阳,孙斐,胡静

• 1:常州工业职业技术学院现代装备制造学院
• 2:常州大学材料科学与工程国家级实验教学示范中心

摘要(Abstract)：

采用光学显微镜、接触角测量仪、显微硬度计等研究了喷砂预处理对20CrMnMo钢气体渗碳效率及渗层特性的影响。结果表明:在相同的气体渗碳工艺条件下,喷砂预处理对20CrMnMo钢气体渗碳具有明显的催渗效果,有效硬化层深度由1.24 mm增加到1.59 mm,即渗碳效率提高了约30%。同时,喷砂预处理使气体渗碳渗层脆性明显降低。

关键词(KeyWords)： 20CrMnMo钢;喷砂处理;气体渗碳;渗碳效率;显微硬度

Abstract:

Keywords:

基金项目(Foundation): 国家自然科学基金(21978025);; 江苏省第三期优势学科建设项目(PAPD);; 江苏高校品牌专业建设工程资助项目(TAPP);; 江苏省高职院校青年教师企业实践培训项目(2020QYSJ124);; 常州工业职业技术学院青年创新基金项目(QN202013101001)

作者(Author): 缪小吉,宋璐,卢阳阳,孙斐,胡静

DOI: 10.13289/j.issn.1009-6264.2020-0359

参考文献(References)：

• [1] Song L,Gu X M,Sun F,et al.Reduced internal oxidation by a rapid carburizing technology enhanced by pre-oxidation for 18CrNiMo7-6 gear steel[J].Vacuum,2019,160:210-212
• [2] Xie F,Hu J,Zhou Z H,et al.Effects of direct current field on powder pack aluminizing[J].Surface Engineering,2011,27(2):134-138
• [3] Cai W,Meng F N,Gao X Y,et al.Effect of QPQ nitriding time on wear and corrosion behavior of 45 carbon steel[J].Applied Surface Science,2012,261:411-414
• [4] Wang S K,Cai W,Li J C,et al.A novel rapid D.C.plasma nitriding at low gas pressure for 304 austenitic stainless steel[J].Materials Letters,2013,105:47-49
• [5] 李景才，孙斐，王树凯，等.离子渗氮前预氧化催渗作用及机理[J].材料热处理学报，2014,35(7):182-186.LI Jing-cai,SUN Fei,WANG Shu-kai,et al.Catalysis effect and mechanism of pre-oxidation on direct current plasma nitriding[J].Transactions of Materials and Heat Treatment,2014,35 (7):182-186.
• [6] Peng T T,Dai M Y,Cai W,et al.The enhancement effect of salt bath preoxidation on salt bath nitriding for AISI 1045 steel[J].Applied Surface Science,2019,484:610-615.
• [7] Miao B,Song L,Chai Y T,et al.The effect of sand blasting pretreatment on plasma nitriding[J].Vacuum,2016,136:46-51.
• [8] Tang L,Jia W J,Hu J,An enhanced rapid plasma nitriding by laser shock peening[J].Materials Letters,2018,231(11):91-93.
• [9] Li D,Wu J Q,Miao B,et al.Enhancement of wear resistance by sand blasting-assisted rapid plasma nitriding for 304 austenitic stainless steel[J].Surface Engineering,2020,36,5:524-530.
• [10] 王仁智.金属材料的喷丸强化原理及其强化机理综述[J].中国表面工程，2012,25(6):1-9.WANG Ren-zhi.Overview on the shot peenig principle and its strengthening mechanisms for metallic materials[J].China Surface Engineering,2012,25(6):1-9.
• [11] Manfridini A P A,Godoy C,Wilson A B,et al.Surface hardening of IF steel by plasma nitriding:Effect of a shot peening pre-treatment[J].Surface and Coatings Technology,2014,260:168-178.
• [12] 缪斌，刘晗，范琪，等.42CrMo钢离子氮碳氧多元共渗及动力学分析[J].材料热处理学报，2016,37(8):184-188.MIAO Bin,LIU Yan,FAN Qi,et al.Plasma oxynitrocarburising of 42CrMo steel and kinetics analysis[J].Transactions of Materials and Heat Treatment,2016,37(8):184-188.
• [13] 钟厉，杨再强，韩西.喷砂预处理与离子氮碳氧硫复合工艺[J].金属热处理，2013,2:112-115.ZHONG Li,YANG Zai-qiang,HAN Xi,et al.Study on sand blasting pretreatment and composite process of plasma nitrogen-carbon-oxygen-sulfuring[J] Heat Treatment of Metals,2013,2:112-115.
• [14] 李亚敏，侯树峰.304不锈钢喷砂助低温渗铝工艺[J].金属热处理，2016,41(12):107-112.LI Ya-min,HOU Shu-feng.The effect of sand blasting on low temperature aluminizing process for 304 stainless steel[J].Heat Treatment of Metals,2016,41(12):107-112.
• [15] 李阳，王梦梦，王元栋，抛丸预处理对渗碳速率影响的研究[J].热处理技术与装备，2020,41(4):21-24.LI Yang,WANG Meng-meng,WANG Yuan-dong.Study on the effect of shot blasting pretreatment on carburizing rate[J].Heat Treatment Technology and Equipment,2020,41(4):21-24.

文章评论(Comment)：